Heat Treatment for Die-Cast Parts

Precision thermal processing that strengthens, stabilizes, and extends the life of your die-cast components. From T5 aging to full T6 solution treatment engineered for your alloy, your spec, your application.

T5 → T7 Full Temper Range

Complete aluminum heat treatment capabilities across all standard designations

±1°C

Temperature Precision

48Hr

Lead Time

Trusted by the companies

ISO 9001:2015

ISO 13485:2016

AS9100D

ITAR Registered

NADCAP Accredited

Why Heat Treatment of Die Cast Parts Is Needed?

01

Eliminate Residual Stress

Rapid solidification during die casting locks internal stresses into the part. Left untreated, these stresses cause warping, cracking, and premature failure under load. Thermal processing relieves stress and restores dimensional stability.

02

Improve Mechanical Properties

Solution treatment and aging dramatically increase tensile strength, yield strength, and hardness. A T6-treated A356 casting can achieve over 260 MPa UTS, nearly double as-cast levels without adding weight or material cost.

03

Stabilize Dimensions

Natural aging continues after casting, causing slow dimensional drift on the shelf. Artificial aging accelerates this process in a controlled furnace environment, locking in final dimensions before the part reaches your assembly line.

04

Enhance Machinability

Annealing and controlled softening reduce work hardening, making subsequent machining, drilling, and forming operations cleaner, faster, and easier on tooling. Fewer passes. Longer tool life. Tighter tolerances.

05

Increase Wear & Fatigue Resistance

Optimized microstructure through thermal cycling significantly improves fatigue life and surface wear resistance, critical for components exposed to cyclic loads, vibration, or friction in service.

RapidoParts Engineering Team

“Precision isn’t just a tolerance spec. It’s a mindset we bring to every pour, every mold, every customer relationship.”

Heat Treatment Services

Most Common · HPDC

T5 Artificial Aging

Parts cool naturally from the die, then are placed directly into a low-temperature aging oven. No solution treatment or quench step ideal for standard high-pressure die castings where blistering risk must be avoided.

→ Aging Temp: 155–165 °C | Duration: 4–8 hrs
→ Typical UTS: 210–230 MPa | Elongation: 3–4%
→ Best For: Instrumentation, electronics, non-structural parts

Max Strength

T6 Solution + Age

The gold standard for maximum mechanical properties. Parts are solution heat treated at high temperature, rapidly quenched, then artificially aged. Dramatically increases hardness, tensile strength, and yield strength.

→ Solution Temp: ~540 °C, 6–12 hrs
→ Quench: Water / Polymer | Age: 160–170 °C, 8–10 hrs
→ Typical UTS: 260–310 MPa | Best For: Structural, automotive, aerospace

High-Temp Stability

T7 Solution + Overaged

Same start as T6, but the aging step is pushed further higher temperature, longer time. Slightly reduced strength in exchange for superior dimensional stability and creep resistance at elevated operating temperatures.

→ Aging Temp: 227 °C / 7–9 hrs | UTS: ~215 MPa
→ Yield: ~200 MPa | Elongation: 3%
→ Best For: Engine components, high-temp service

Stress Relief

Annealing

Controlled heating to reduce hardness, relieve internal stress, and restore ductility. Enables downstream straightening, forming, or machining operations on parts that would otherwise crack or distort.

→ Temp Range: 250–400 °C depending on alloy
→ Result: Reduced hardness, improved plasticity
→ Best For: Pre-machining treatment, weld prep, distorted castings

Precipitation

Solution Heat Treatment

Parts are held at an elevated soak temperature long enough for alloying elements to dissolve into solid solution. Rapid quenching traps these elements in a supersaturated state, priming the microstructure for subsequent aging.

→ Temp: 505–540 °C | Duration: 4–12 hrs
→ Quench Media: Water, hot water, polymer
→ Always followed by: T4, T6, or T7 aging

Dimension Lock

Stress Relieving

Lower-temperature thermal cycling that reduces residual stress from casting, machining, or welding without significantly altering mechanical properties. Prevents in-service distortion and improves part longevity.

→ Temp Range: 150–300 °C
→ Duration: 2–6 hrs depending on alloy and wall thickness
→ Best For: Post-weld treatment, machined components

Natural Age

T4 Solution + Natural Age

Parts are solution treated and quenched, then allowed to age at room temperature. Achieves good ductility with moderate strength no furnace aging required. Slower process but ideal when ductility is the primary requirement.

→ Hold Time: 18–24 hrs at room temperature
→ Typical UTS: ~200 MPa | Elongation: 4–6%
→ Best For: Formable structural components, brackets

Hardness Check

Hardness Testing

Every heat treatment cycle at RapidoParts is followed by hardness verification. We use Brinell and Rockwell testing to confirm that parts have achieved target properties before release fully documented and traceable.

→ Methods: Brinell (HB), Rockwell (HRB)
→ Reporting: Test records with every batch
→ Traceability: Lot-level documentation available

Alloys

Heat Treatment Alloys at RapidoParts

Alloy Base Metal Cast Process Compatible Treatments Typical UTS Hardness Primary Use Case
A380
Aluminum
HPDC
T5, Anneal, Stress Relieve
~220 MPa
~75 HB
Housings, brackets, enclosures
A356
Aluminum
Sand / Perm. Mold
T4, T5, T6, T7
260–310 MPa
80–85 HB
Structural automotive, suspension
A319
Aluminum
Sand / Perm. Mold
T5, T6, T7
~250 MPa
~75 HB
Engine blocks, cylinder heads
A413
Aluminum
HPDC
T5, T6
>280 MPa
~80 HB
Pump housings, valve bodies
6061
Aluminum
Wrought / Cast
T4, T6, T651
240–270 MPa
~95 HB
Aerospace frames, structural members
6063
Aluminum
Wrought / Cast
T5, T6
~210 MPa
~73 HB
Enclosures, heat sinks, trims
ZA-8
Zinc-Aluminum
HPDC / Gravity
Aging, Stress Relieve
~250 MPa
~100 HB
Hardware, plumbing, bearings
ZA-27
Zinc-Aluminum
HPDC / Gravity
Aging, Anneal
~400 MPa
~120 HB
Gears, wear parts, high-load components
AM60
Magnesium
HPDC
T5, Anneal
~220 MPa
~60 HB
Automotive seat frames, instrument panels
AZ91D
Magnesium
HPDC
T4, T6, Stress Relieve
~230 MPa
~63 HB
Powertrain covers, lightweight structures
Custom
Any
Any
By Spec
,
,
Proprietary alloys , recipe developed on request

T-Designation Quick Reference

Designation Process Description Typical UTS Elongation Common Applications
T4
Solution treated + naturally aged at room temperature
~200 MPa
4–6%
Brackets, formable structural parts
T5
Cooled from die, artificially aged (no solution step)
210–230 MPa
3–4%
Electronics, instruments, housings
T6
Solution treated → quench → artificially aged
260–310 MPa
3–5%
Automotive, aerospace, structural components
T7
Solution treated → quench → over-aged (higher temp)
~215 MPa
3–4%
Engine parts, high-temperature service
T71
Same as T7 but aged at lower temperature / shorter time
~170 MPa
3.5%
Parts requiring maximum dimensional stability
Anneal
Heated to reduce hardness, improve ductility
Varies
Improved
Pre-machining, stress relief, weld prep

Industries We Serve

Heat treated die cast parts from RapidoParts operate in some of the most demanding environments in the world.

Automotive

Engine brackets, transmission housings, structural nodes, EV battery enclosures

Aerospace & Defense

Flight-critical brackets, landing gear components, avionics housings

Medical Devices

Imaging equipment frames, instrument housings, surgical tool bodies

Robotics & Automation

Arm joints, encoder housings, end-effector components requiring tight tolerances

Electronics & Semiconductor

Heat sinks, RF shields, enclosures requiring dimensional precision after processing

Marine & Oil & Gas

Corrosion-critical parts requiring maximum strength and surface stability

Industrial Equipment

Pump housings, valve bodies, hydraulic components, wear surfaces

EV & Clean Energy

Battery module frames, motor housings, inverter enclosures for electric vehicles

Built to Your Spec

Every heat treatment cycle at RapidoParts is engineered, monitored, and verified. We don’t guess at temperatures or rely on manual timers. Our furnaces are calibrated, data-logged, and regularly surveyed to AMS 2750 pyrometry standards.

  • Full furnace calibration and temperature uniformity surveys
  • Lot-level traceability with time/temperature data logging
  • Hardness testing on every batch before shipment
  • First Article capability for new programs
  • Customer-specific reporting formats available
  • Metallurgical support for alloy selection and process specification